Finden Sie schnell maske aus metall für Ihr Unternehmen: 4 Ergebnisse

Wir liefern Teigmulden für verschiedene Gäranlagen, Gärschränke, z. B. für WP Haton, Kemper, Baker Perkins, Benier, Subal, etc. ----- English below ----- Wir liefern Teigmulden für verschiedene Gäranlagen, z. B. für WP Haton, Kemper, Baker Perkins, Benier, Subal, etc. Dank der Spezialisierung auf eine Nische kann unser Hersteller auch Sonderanfertigungen für andere Marke produzieren. Normalerweise werden Teigmulden sehr schnell durch Bakterien in Gärschranken angegriffen. Unser Hersteller anfertigt Teigmulden aus Materials mit erhöhter Lebensdauer und verbessert ständig seine qualitative Produktpalette. ______________________ We offer mesh pockets for intermediate proofers manufactured by APV, Benier, Baker Perkins, Gefra, Glimek, Globe, Gostol, Gouet, Kemper, König, Op t Root, Peeters, Spronk, Sottoriva, Subal, Ter Haar, Van Dijk, Winkler, WP Haton. The make-to-order for other brands is also possible. As a rule, mesh pockets are very quickly exposed to bacteria in the proofers and become unfit for use. Therefore, we selected the reinforced materials and manufacturers constantly improving their quality and range of products. Thanks to special antibacterial additives and UV stabilizer, moldiness is not formed on the mesh pockets, thus, they are safe for use in food industry for the whole service life. Material: polyethylene with antibacterial additives "Anti Mikroben Additive" and UV stabilizer.

Wir liefern etablierte Metallpulver wie AlSi10Mg, Titanpulver, Werkzeugstahl, Edelstahl und Kobalt-Chrom sowie unsere eigenen Aluminium-Magnesiumlegierungen (AlMgty) mit besonders hoher Dehnung. Als unabhängiger Händler vertreibt Fehrmann neben High-Performance-Legierungen, auch etablierte 3D-Druckpulver. Dazu zählen Werkzeugstahlpulver, Edelstahlpulver 316L, AlSi10Mg, TiAl6V4 Legierungspulver (fein/grob) und CoCr Pulver. Durch eine Hochskalierung der Mengen, kombiniert mit optimierter Lagerhaltung und Qualitätssicherung, kombinieren wir die Vorteile des internationalen Handels mit den Verfügbarkeits- und Qualitätsansprüchen unserer Kunden und fördern den industriellen 3D-Druck.

Metal stitching is a very well-established repair method. It is applicable to a wide variety of materials such as cast iron, cast steel and many non-ferrous metals. Metal stitching, sometimes also called cold pinning, has been around for over 100 years. It is a very well established and proven technology. It is mostly used on cast (gray) iron components such as engine blocks and casings although the repair of other materials such as aluminium and bronze is possible too. The advantages of metal stitching are many: ✦Usually, little or no dismantling is necessary. Proper access from one side is generally sufficient. ✦Since it is a cold-repair method, no additional stresses, which over time may lead to new cracks, are introduced into the material. ✦The original alignments of the parts can be retained. There is no deformation or blemish due to the application of heat. Re-machining after repair is therefore often not necessary. ✦The repair seam helps to distribute tensile stresses over a larger area ✦If done properly, then the repaired area is liquid and gas tight. QuantiServ has successfully applied water pressure up to 12 bars (174 psi) to a test piece that was repaired by metal stitching. ✦And last but not least, our metal stitching repairs qualify as permanent repairs! The cracked metal is replaced with special metal stitching pins that we install by drilling and tapping to draw the sides of the crack together. This results in a continuous row of interlocking stitching pins to create a strong, pressure-tight repair. To restore the casting to its original strength, we install locks across the joint line of the pins by drilling a precision hole pattern with special drill fixtures. After the hole pattern is created, the locks are driven in, pulling the material together even tighter. Finally, the stitched area is ground to conform to the base metal contour, thus completing the repair. If the component undergoing repair is not only cracked but if a piece is missing, then we prefabricate a new piece and lock it in place in the same manner as described above. We are selling the majority of our crack repair tools and supplies to enable our customers to carry out small and non-complex repairs by themselves. Stitching pins Our metal stitching pins are equipped with special, proprietary threads that exert a radial pulling force during tightening. They therefore pull the crack together and seal it. The majority of stitching pins that we use are made of high-grade steel. Steel pins, being stronger than cast iron, are usually used to repair cracks in cast iron bodies. For special applications, aluminum, stainless and bronze stitching pins are also available. Depending on the application, we offer two different series of stitching pins to choose from: The top-of-the line, very strong C-Series pins that are designed to not create radial spreading forces and the economical L-Series ones that are meant for applications that carry fewer structural loads.

Druck-/wasserdicht bis 0,15 bar, heißwasser-/wasserdampfbeständig bis 150°C & korrosionsbeständig: zu öffnende Schaugläser mit/ohne Scheibenwischer & Deckel für den Anlagenbau , Klärwerke & Faultürme Wir liefern Fenster für diverse Anwendungen im Anlagenbau (zum Beispiel Kläranlagen, Gasbehälter, Reinigungs- und Abfüllanlagen) stellen wir druckdichte feste und zu öffnende Schaugläser mit Scheibenwischer und Deckel als Beobachtungsfenster, Revisionsfenster und -türen her. Die Konstruktionen sind Maßanfertigungen oder Produkte auf Basis unseres Baukastensystems und können den jeweiligen Anforderungen angepasst werden. Die von uns in Edelstahl, Leichtmetall oder Schwermetall hergestellten Sicherheitsbauteile sind druckdicht bis zu 0,15 bar. Als Dichtungen verwenden wir hochwertige Neoprene-, Viton- bzw. Silikondichtungen. Sämtliche Produkte erfüllen höchste Sicherheitsstandards, sind von langlebiger Qualität und wartungsfrei.